Megger 1002-001 Loop Impedance Tester 2 Wire Test Lead Set, For Use With MIT 300 Series

  • RS Stock No. 480-1778
  • Mfr. Part No. 1002-001
  • Manufacturer Megger
Technical data sheets
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): GB
Product Details

RCDT310 & RCDT320 RCD Testers

Two RCD testers that comply with EN61557 for testing, measuring or monitoring of protective measures.

Tests 30mA, 100mA, 300mA and 500mA rated RCDs
1/2x I, I, 5x I tests standard, DC and selective RCDs
0° or 180° polarity tests on all RCDs
Selective breakers have a time delay in tripping. When selected, trip test times are extended and a 30s delay is allowed between the measurement of the fault voltage and the application of the test current
Selectable touch voltage inhibit and touch voltage display on the analogue bargraph
300Vac (25 to 45Hz) voltage measurement range
Clear 20mm high digit LCD display with analogue arc bargraph
Tough rubber armoured case with self-contained display cover that locks away underneath the instrument during use
Safety input terminal interlock - prevents unsafe connection of test leads
Safety lock-out prevents the test from operating when the circuit voltage is >300V

RCDT320 model additional features

10mA/1A RCD extended test capability
Backlit display and range selection ideal for low light environments
Ramp Test measures & displays the actual trip current of an RCD. Ideal for diagnosing nuisance tripping of RCDs
Auto testing allows remote testing from the RCD under test. The RCDT320 will automatically perform a 1//2 I, I and 5I test at both 0°and 180°. When the RCD trips the user resets it and the tester proceeds to the next test automatically. All results are displayed at the end of the test
25 to 450Hz Frequency measurement range
Optional 2-wire test leads supplied

3-phase safe - Meets the requirements of BSEN 61010-1 for safe connection to a 440V Installation Category III supply (300V phase to Earth)
Weatherproof to IP54
Dimensions (WxHxD): 190 x 75 x 140mm; Weight 980g

Note

RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty

Supplied with

Instructions, Mains plug test leads, 8 AA alkaline batteries, neck strap.

Megger Insulation Tester Leads

The Megger insulation tester lead is a set of two leads used for BM100 insulation and continuity tester. This tester is used as a replacement or spare test lead set. These leads have 4mm connector and can be used with a range of multimeters, clamp meters, insulation testers, multifunction testers & continuity testers. For insertion into a difficult application, it has an extremely thin width, the length of the test leads is approximately 120cm, and that of the finger probes is 9cm.
Supplied with:
instructions, 2 wire test lead set with crocodile clips, 8 x AA alkaline batteries, neck strap & carry case.

Features and Benefits


Double insulated for additional protection
• Red and Black Leads
• 4mm Right Angle Plugs on Instrument End
• 4mm Safety Probes and Croc Clips on Test End

Certifications


CAT III 1000 V

Specifications
Attribute Value
Accessory Type 2 Wire Test Lead Set
For Use With MIT 300 Series
29 In Global stock for delivery within 4 - 6 working days
Price Each
MYR 320.92
units
Per unit
1 +
MYR320.92
Related Products
Kits for performing tests required by NF C ...
Description:
Kits for performing tests required by NF C 15-1001 DT-170 (differential controller)1 DT-300 (earth and continuity measuring device and extension cord)1 M-9955538 (diagnostic book 15-100)1 DT-500* (Insulation controller and connectors).
Set of 2 spare leads for DTR8510 and ...
Description:
Set of 2 spare leads for DTR8510 and DTR8500. Length 4.6m.
Earth loop impedance testers to verify the loop ...
Description:
Earth loop impedance testers to verify the loop impedance of a live electrical circuit without the need to disconnect the electrical supply. The LTW300 series instruments offer a safe and easy 2 wire loop testing solution that does not trip ...
RS Pro IPT1800 is a great value, microprocessor-controlled ...
Description:
RS Pro IPT1800 is a great value, microprocessor-controlled PSC/loop tester. Its high loop impedance range permits direct measurement of ground spikes. Features include an auto lock-out if the test resister overheats. Large 3 digit 2000 count with analog bargraph LCD200 ...