STMicroelectronics X-NUCLEO-PLC01A1 PLC Driver for STM32 Nucleo

Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

X-NUCLEO-PLC01A1 Industrial PLC Expansion Board

The X-NUCLEO-PLC01A1 is an input/output expansion board which provides an STM32 Nucleo MCU board with industrial PLC (Programmable Logic Controller) functionality.

• 8 x inputs protected by a CLT01-38SQ7 digital termination array • 8 x outputs driving a VNI8200XP octal high-side solid-state relay
• Host communication: SPI bus protected by on-board Si8661 digital isolator
• Status LEDs: Power OK, SPI Activity, Fault, Over-temperature
• 16 x I/O activity LEDs
• Screw connectors for all protected I/O
• Compatible with STM32 Nucleo-64 MCU boards
• Arduino Uno r3 compatible Shield headers
• Designed for situations required to pass IEC61000-4-2 8kV and 15kV test standards
• Free development firmware and example library compatible with STM32Cube firmware

Suitable STM32 Nucleo MCU Boards

802-9412 NUCLEO-F030R8 Cortex-M0 core processor 802-9416 NUCLEO-F103RB Cortex-M3 core processor
802-9425 NUCLEO-F401RE Cortex-M4F core processor

STM32F4 Series 32-Bit ARM Cortex-M4 Microcontrollers, STMicroelectronics

The ARM Cortex-M4 based STM32 F4 series of high-performance MCUs with DSP and FPU instructions is an extension of the industry-leading STM32 portfolio towards even higher performance. Up to 180 MHz operating frequency.

Up to 2x USB 2.0 OTG FS/HS
SDIO (Secure Digital Input Output)
USART, SPI, I²C
I²S (Inter-IC Sound) + Audio PLL
16 and 32 Bit Timers
Up to 3x 12-Bit ADC
Low Voltage 1.7 V to 3.6 V

Specifications
Attribute Value
Power Management Function PLC Driver
Kit Classification Expansion Board
For Use With STM32 Nucleo
3 In Global stock for delivery within 4 - 6 working days
Price Each
MYR 57.67
units
Per unit
1 +
MYR57.67
Related Products
The STEVAL-ISB041V1 board is based on an STBC02 ...
Description:
The STEVAL-ISB041V1 board is based on an STBC02 battery power management chip, integrating a linear charger for single-cell Li-Ion batteries with protection functions, an LDO regulator, two SPDT load switches and intelligent reset logic. It will charge single-cell Li-Ion/Li-Po batteries ...
The demo board supports the LDO regulator NCP3337 ...
Description:
The demo board supports the LDO regulator NCP3337 in DFN10 package with adjustable output voltage. The ENABLE function allows turn the device to low consumption mode with quiescent current below 1 μA. The Power Good pin allows output voltage monitoring. ...
The NCP101X series integrates a fixed-frequency current-mode controller ...
Description:
The NCP101X series integrates a fixed-frequency current-mode controller and a 700 V voltage MOSFET. Housed in a PDIP7 package, the NCP101X offers everything needed to build a rugged and low-cost power supply, including soft-start, frequency jittering, short-circuit protection, skip-cycle, a ...
The UIC1WGEVB evaluation board showcases a simple, low ...
Description:
The UIC1WGEVB evaluation board showcases a simple, low cost, low part count chopper topology circuit. It is designed to safely operate with input voltages varying from 80 VAC to 280 VAC. ON Semiconductor CCRs are used to provide constant LED ...