Recently searched

    Mean Well DRP Switch Mode DIN Rail Panel Mount Power Supply, 85 → 264V ac ac Input, 24V dc dc Output, 10A

    RS Stock No.:
    Mfr. Part No.:
    Mean Well
    Mean Well
    View all DIN Rail Power Supplies
    Discontinued product
    RS Stock No.:
    Mfr. Part No.:
    Mean Well
    COO (Country of Origin):

    Legislation and Compliance

    COO (Country of Origin):

    Product Details

    Mean Well DRP Series Single Output Power Supply

    A range of single phase DIN Rail power supplies from Mean Well with a fanless design and wattages available between 45 W and 480 W.

    Features and Benefits

    • Universal AC input/Full range

    • Protections: Short circuit/Overload/Over voltage/Over temperature

    • Cooling by free air convection

    • Can be installed on DIN Rail TS-35/7.5 or 15

    • UL 508 (industrial control equipment) approved

    • LED indicator for power-on

    • 100% full load burn-in test

    • Fix switching frequency at 100 kHz

    • 3 years warranty

    • Built-in active PFC function

    Product Application Information

    The units are suitable for powering security and building automation controls which are increasingly required in commercial and residential premises.

    Why use a DIN Rail Power Supply?

    The flexibility of DIN Rail mounting systems enables quicker installation time as all devices are able to simply snap onto the metal rails. Power supplies can be easily organised on DIN Rails within enclosed wall boxes or in areas where there is limited space. Similar devices can be mounted next to each other reducing the amount of cabling required. Most power supplies are convection cooled so no cooling fans are needed.
    DIN Rail AC/DC power supplies are widely used in many automation, instrumentation and industrial applications. They are used to power a wide variety of DC operated devices including sensors, motors, actuators, solenoids and relays.

    Points to Consider When Buying a DIN Rail Power Supply

    DIN Rail size – There are three common types of DIN Rails. Top Hat, G section and C section. Most have a depth of 7.5 mm or 15 mm. It is wise to check that your power supply is compatible with your DIN Rail.

    Protection Types – It is important to choose a power supply that is protected against either short circuit, overload, over temperature or over voltage. Some power supplies also offer a hiccup mode which will allow the PSU to resume operation once the fault is cleared.

    Fixed or adjustable output voltage or current – In test systems it is often convenient to have adjustable DC voltage however in other applications a fixed DC supply may be essential.

    Cabling and wiring – The input/output lines to and from the power supply should be as short as possible with a large cross sectional area to help minimise noise and heat.

    Efficiency – Choose a power supply that has an efficiency over 89% to minimise the amount of power dissipation, especially if the system relies on convection cooling.

    Input voltage range – If the DIN Rail power supply you are buying is to be used in Europe and North America as well as the UK then a universal AC input range of 80 V ac to 264 V ac is required.

    Standards – If the power supply is to be used in the USA for controlling electric motors then it will need to comply with Standard UL508, the safety standard for industrial control equipment.


    UL508, TUV EN60950-1 approved
    Mean Well DRP series 240 W, 24 V dc, 10 A DIN Rail power supply.


    Output Voltage24V dc
    Output Current10A
    AC or DC Input Voltageac
    AC or DC Output Voltagedc
    Input Voltage85 → 264V ac
    Power Rating240W
    Electrical Phase1
    Number of Outputs1
    Mounting TypeDIN Rail Mount
    TypeSwitch Mode
    Minimum Temperature-10°C
    Maximum Temperature+70°C
    Output Voltage Adjustment Range24 → 28V
    Load Regulation±1%
    Ripple And Noise80mV Pk-Pk
    Special FeaturesOvervoltage and Short Circuit Protection
    Standards MetRoHS Compliant, TUV EN 60950-1, UL 508
    Discontinued product