Arbors

An arbor or mandrill is an attachment that is used with a hole saw and power drill to cut holes in metal, plastic and wood. The arbor is made up of three sections:
  • Arbor shaft – This end of the attachment is the section that fits into the chuck of the power drill.
  • Central collar – The central collar is the middle part of the arbor with a short threaded section on the underside of the collar base.
  • Pilot bit - The pilot bit is a drill bit fixed into the central collar through the threaded portion on the underside of the collar head.
What does it do?An arbor is a way of temporarily securing a hole saw to a power drill to enable cutting of circular holes in metal, plastic or wood. The arbor shaft is fixed into the chuck of the power drill. The hole saw is attached to the arbor through a small hole at the centre back of the hole saw. The saw is secured to the arbor by screwing the thread at the back of the hole saw to the threaded section under the central collar. Why do you need it?Hole saws and arbors are used in a wide variety of applications. The most common environments are:
  • Lighting - Cutting the hole in a ceiling before installing light fixtures
  • Drainage - Cutting holes in walls before installing waste pipes.
  • Pipework and plumbing - Cutting access holes for plumbing and pipelines.
  • Electrical cables and wiring - Cutting access holes in preparation for electric wiring connections.
TypesThere are two sizes of arbor:
  • Small arbor - 6.5mm – The 6.5mm arbor is used with hole saws with diameters in the 14mm to 32 mm range
  • Large arbor - 9.5mm – The 9.5mm arbor is used with hole saws with diameters in the 32mm to 152mm range

...
Read more Read less

Filters

Viewing 1 - 9 of 9 products
Results per page
Description Price Supported Holesaw Size Diameter Bimetal
RS Stock No. 215-978
BrandRS PRO
MYR70.03
Each
units
32 → 152mm 9.5mm Yes
RS Stock No. 216-044
BrandRS PRO
MYR36.47
Each
units
14 → 30mm 6.5mm Yes
RS Stock No. 615-258
Mfr. Part No.BC884
BrandStarrett
MYR126.69
Each
units
32 → 152mm 1/4in Yes
RS Stock No. 615-242
Mfr. Part No.BC882
BrandStarrett
MYR46.00
Each
units
14 → 30mm 1/4in Yes
RS Stock No. 174-6857
Mfr. Part No.3084712X
BrandLenox
MYR94.72
Each
units
1L mm, 2L mm, 3L mm 12.7mm -
RS Stock No. 174-6858
Mfr. Part No.1768811
BrandLenox
MYR156.62
Each
units
20 → 96L 12.7mm -
RS Stock No. 174-6860
Mfr. Part No.1768813
BrandLenox
MYR145.05
Each
units
32 → 152mm 9.5mm -
RS Stock No. 174-6859
Mfr. Part No.1768812
BrandLenox
MYR105.37
Each
units
14 → 30mm 9.5mm -
RS Stock No. 145-8338
Mfr. Part No.0 546 99
BrandLegrand
MYR178.15
Each
units
- - -
Related Products
Allows full range of hole saws (14mm to ...
Description:
Allows full range of hole saws (14mm to 152mm) to be usedSDS bits for use with SDS chuck power toolsHexagon and plain shank arbors for use with three-jaw chuck power toolsRework adaptor, enables enlargement of an existing holeSet contains: One ...
HSS step drill with straight tap, two-edgedTiAlN coating, ...
Description:
HSS step drill with straight tap, two-edgedTiAlN coating, for particularly tough materialsFor burr-free drilling and planing sheet metal, pipes and profilesNo centre-punching necessary, drill bits do not runSuitable for construction steel, CrNi steel, non-ferrous metals, Plexiglas, plastics and wood up ...
Raptor Cutters from Rotabroach. These annular cutters are ...
Description:
Raptor Cutters from Rotabroach. These annular cutters are hole cutting tools used on piping, tubing or material that require a fine finish hole cut. Raptor cutters optimise cutting edge geometry for increased cutting performance and reduced cutting forces. Offers effective ...
• Hardened cutting edge (6tpi alternate set) welded ...
Description:
• Hardened cutting edge (6tpi alternate set) welded to a tough alloy steel body• Bonded construction reduces possibility of shattering• For use with ferrous and non ferrous metals, plastics and wood to a depth of 32 mm• 14 to 30 ...